To make buttonholes with a sewing machine, reinforce the fabric, mark each opening, attach the correct buttonhole foot and sew using your machine’s one-step or four-step setting. Test the size on matching scraps before stitching your garment, then cut between the stitched sides without cutting the end bars.
Prepare your sewing machine and fabric
You’ll need your button, matching thread, a suitable needle, a buttonhole foot, removable marking tools and a seam ripper or buttonhole cutter. Check your machine’s manual for its buttonhole settings and the correct foot, since attachment methods and stitch sequences differ.
Choose a needle that suits your fabric: a sharp or universal needle for most woven fabrics, or a stretch needle if your fabric needs one. Switch off the machine before changing the needle or presser foot. Thread the machine normally and start with the recommended tension rather than tightening it to make the stitching denser.
Interface the buttonhole area to support the dense stitching. On a garment, you’ll usually apply suitable interfacing to the facing, waistband or button band before assembly. For stretchy or loosely woven fabrics, you may also need a temporary stabilizer to support the fabric during stitching.
Prepare a test piece with the same fabric layers, interfacing and seam allowances as the finished area. Testing on a single layer won’t show you how the machine will feed a thick, finished button band.
How to measure and mark buttonholes
Your finished opening needs to accommodate both the button’s diameter and its thickness. If you’re setting the buttonhole length manually, use the diameter plus the button’s thickness as a starting point, then test the fit. Thick or unusually shaped buttons may need more room.
With many automatic buttonhole feet, you place the button in an adjustable holder that determines the stitching length. You still need to test that setting because the actual opening depends on the machine, stitch settings and button shape.
Follow your pattern’s placement marks if it provides them. Otherwise, mark the garment’s centre-front line and button positions before marking each opening. For horizontal buttonholes, you’ll commonly extend the opening slightly beyond the centre-front line towards the opening edge. For vertical buttonholes, you’ll usually place the opening along that line.
Clearly mark the direction and endpoints of each opening. Keep every buttonhole far enough from the finished edge to leave intact fabric beside the stitching, and avoid placing the foot partly on a bulky seam if possible.
How to sew a one-step buttonhole
With a one-step setting, your machine stitches the sides and end bars in one programmed sequence. Some machines stop automatically; with others, you need to stop when the cycle finishes. Follow your manual’s starting-point diagram because the machine may sew backwards first.
- Fit the automatic buttonhole foot, place the button in its holder and select the buttonhole stitch you need.
- Lower the buttonhole sensor lever fully if your machine uses one. Check that it sits in the position shown in the manual, usually beside a stop on the foot.
- Place the fabric under the foot and align your marked starting point with the foot’s reference marks. Position the thread tails as your manual directs.
- Lower the presser foot and sew at a steady, moderate speed. Guide the fabric lightly without pulling it or obstructing the foot’s sliding section.
- Complete the full cycle, stop with the needle raised and lift the foot before removing the fabric. Reset the cycle as instructed before sewing another buttonhole.
- Cut open the test buttonhole and pass the actual button through it. Adjust the size or settings before stitching the garment.
Test the button’s fit rather than judging the stitched rectangle alone. You should be able to pass the button through without forcing it or stretching the opening, but it shouldn’t slip out easily.
How to sew a four-step buttonhole
A four-step setting lets you control the length while the machine supplies the stitch pattern for each part. Follow your machine’s selector symbols to sew the stages in the correct order. Don’t assume every model starts with the same side.
- Select the first stage and stitch to the marked endpoint, or sew the first end bar if your machine starts there.
- Stop with the needle raised, select the next stage and sew the section shown in the machine’s diagram.
- Continue through the remaining stages, stopping the side stitching at your marked endpoints and keeping the end bars compact.
- Secure the stitches as your manual directs, then raise the needle and remove the fabric.
Use the recommended buttonhole stitch length to produce closely spaced zigzag stitches. Aim for dense stitching, not piled-up stitches: the fabric still needs to move under the foot. If your machine has adjustable stitch width, start with its recommended setting and change it only after examining your test buttonhole.
How to cut a buttonhole open safely
Inspect the stitching before cutting. Check that both sides are secure and that the end bars, also called bartacks, close the ends. Repair any missing stitches before cutting the fabric.
Place a pin across the opening just inside each bartack to help prevent you from cutting past it. With a sharp seam ripper, make a small opening near the centre and cut towards one end, then reverse direction to cut towards the other. Keep your fingers away from the cutting path.
Never cut through the bartacks or the side stitching. If you use a buttonhole cutter, place a suitable cutting block underneath and keep the blade within the stitched opening. Trim loose fabric fibres carefully without clipping the thread.
How to fix common buttonhole problems
If the fabric puckers, check your interfacing and needle first. Try a temporary stabilizer, reduce excessive stitch density and check that you’ve threaded the upper thread correctly through the tension system.
If one side looks different from the other, check for uneven fabric thickness or a foot that doesn’t sit level. If your machine has a buttonhole balance adjustment, you can use it to correct differences between forward and reverse feeding. Follow the manual’s instructions.
If an automatic cycle stops early or keeps stitching in one place, check the sensor lever, button holder and foot attachment. Keep the sliding foot clear of seams and fabric folds, then restart on a fresh test area rather than repeatedly stitching over the faulty buttonhole.