Home

Why Is My Sewing Machine Not Feeding Fabric?

If your sewing machine isn't feeding fabric, check for lowered feed dogs, a raised presser foot, a stitch length set to zero or thread tangled beneath the needle plate. If the fabric still won't move after these checks, look for packed lint, incorrect presser foot pressure or a mechanical fault.

Check your sewing machine settings

The feed dogs are the toothed metal strips beneath the presser foot. They rise through the needle plate, grip the underside of the fabric and move it forward between stitches. The presser foot holds the fabric against them, so both parts need to work together.

Before you change the tension or take anything apart, run through these checks:

  • Lower the presser foot before sewing. Some machines can run with the foot raised but won't feed fabric properly.
  • Select a regular straight stitch rather than a buttonhole, darning or free-motion setting.
  • Set the stitch length above zero. Around 2.5 mm is a useful starting point for testing ordinary woven cotton.
  • Check that you've disengaged the bobbin-winding mechanism and, if your machine has a handwheel clutch, engaged the clutch.
  • Check that the reverse button or lever has returned to its normal position.

Test on two layers of medium-weight woven cotton. If they feed normally, your project fabric, presser foot or seam thickness is more likely to be causing the problem than the basic feeding mechanism.

Check whether the feed dogs are raised

You may have left the feed dogs lowered after free-motion quilting, embroidery or darning. Use your machine's manual to locate the drop-feed control. You may find it behind the free arm, near the bobbin area or on the back of the machine.

Move the control to the sewing position. On many machines, the teeth don't rise immediately: you need to turn the handwheel through a complete stitch cycle in the direction your manual specifies. Some models use a cover plate instead of retractable feed dogs, so check that you haven't left a darning plate over the teeth.

Switch off the machine, raise the presser foot and turn the handwheel slowly. During a normal forward stitch, you should see the teeth rise, move towards the back of the machine, drop and return. They won't stay above the plate throughout the cycle.

Remove lint and tangled thread

Packed lint between the feed-dog teeth can reduce their grip. A nest of tangled thread beneath the fabric can also hold your work in place even though the needle keeps moving.

Switch off and unplug the machine before you remove the needle plate or clean around moving parts. Follow your manual's instructions for accessing the bobbin area, then work through these steps:

  1. Raise the needle and presser foot. If the fabric is trapped, cut any threads you can reach rather than pulling it free.
  2. Remove the bobbin and any removable bobbin holder only as your manual directs.
  3. Brush lint from the feed-dog grooves, beneath the needle plate and around the bobbin area.
  4. Check the bobbin holder for loose thread, then refit every part securely.
  5. Rethread the upper thread with the presser foot raised, reinstall the bobbin correctly and test on scraps.

Don't loosen the feed-dog mounting screws or add oil unless your manual specifically tells you to. Avoid using compressed air, which can blow debris further into the machine.

If thread bunches underneath again, check the upper threading before you adjust the bobbin tension. If you miss the take-up lever or tension discs when threading, the upper thread can form loops beneath the fabric and stop it moving forward.

How to stop fabric getting stuck at the start

If your fabric feeds normally after the first few stitches but jams at the start of a seam, you may not have enough fabric covering the feed dogs. A blunt or unsuitable needle can also push fine fabric into the needle opening.

Start with the fabric supported beneath the foot, not barely touching its front edge. Hold the thread tails lightly behind the foot for the first few stitches without pulling them, unless your machine's instructions say otherwise.

For delicate fabric, fit a fresh needle of the recommended type and size. A straight-stitch plate can help support thin material, but use only compatible straight stitches with it. If you select a zigzag or another stitch that moves the needle sideways, the needle can strike the plate.

A small scrap of fabric, often called a leader, can also help. Begin sewing on the scrap, then feed your project directly behind it so the foot stays supported as you start the seam.

Choose the right presser foot and pressure

If ordinary cotton feeds correctly but your project doesn't, check the presser foot and its pressure. Too little pressure lets the fabric slip; too much can stretch knits or cause drag on fabrics that don't slide easily under the foot. Adjust the pressure only if your machine has a pressure control, and test small changes on scraps.

A compatible walking foot can help several layers move forward together. A non-stick or roller foot may feed coated or tacky surfaces more effectively than a standard metal foot. Neither will solve a problem caused by lowered feed dogs or a thread jam.

At a thick seam intersection, the foot can tilt and lose contact with the fabric. Use a suitable seam-leveling tool according to its instructions, slow down and don't exceed your machine's capacity.

Don't pull the fabric to make it move. Guide it gently instead. Pulling can bend the needle and cause it to strike the foot or needle plate.

When to get professional repairs

If your machine feeds backwards, first check the reverse control and your selected stitch. Some decorative stitches deliberately move backwards for part of their pattern. Switch to a basic straight stitch before you assume the mechanism that controls the feed direction is faulty.

Arrange professional servicing if the reverse control sticks or the feed dogs fail to rise after you follow the correct reset procedure. You should also seek repairs if the feed dogs move but still won't advance ordinary test fabric after cleaning and basic checks. A technician may need to replace worn teeth, secure loose components or adjust the feed timing inside the machine.

Stop sewing immediately if you hear grinding, the handwheel becomes unusually stiff or the needle strikes metal. Don't force the handwheel or attempt timing adjustments without the appropriate service knowledge. Tell the technician which checks you've completed and whether the fault began after a jam or needle strike.